Optimising your design for MIM production

Several aspects of the MIM component design improve the ease of manufacturing, and there are a number of design features that should be avoided. These are categorised as follows:

Desirable features ✔

  • gradual section thickness changes
  • wall thickness larger than 0.1 mm but below 10 mm
  • low mass
  • one flat surface for support during sintering

Allowed design features ✔

  • axisymmetric, nonsymmetric, prismatic, square, and freeform features
  • cantilever and nonsymmetric shapes
  • stiffening ribs and locator features for assembly
  • protrusions, bosses, and studs
  • most hole shapes are allowed, including blind and through holes
  • holes at angles to one another
  • undercuts, grooves, slots, depressions
  • external teeth, external or internal threads
  • knurled and waffle surfaces
  • part number or identification logo created by the mould

Features to avoid X

  • inside closed cavities
  • undercuts on internal bores
  • very sharp corners or edges – desired radius greater than 0.05 mm
  • long pieces without a draft or taper to allow ejection
  • holes under 0.1 mm in diameter
  • walls thinner than 0.1 mm
THE WORLD OF MIM, CIM and SINTER-BASED AM TO YOUR INBOX
Subscribe to our weekly newsletter
Sign up

Be aware of size limitations

Some of the limitations arise from the moulding equipment. Massive parts (12 to 17 kg), long components (up to 300 mm), and thick sections (125 mm) have been demonstrated.

Optimising your design for MIM production - Fig_7
Fig. 7 An illustration of how moulding cycle time increases with component section thickness

In MIM, the component size is not so much an inherent process limitation as an issue from the capacity of the installed equipment and the rapid increase in cost with thick structures, since moulding, debinding, and sintering are all faster with thin walls.

Fig. 7 shows how the moulding cycle time increases with wall thickness. Remembering that time is money, this plot shows the clear advantage in shorter cycle times for designs involving hollowed out components with thinner walls.

Small design modifications can make a big difference

In general, the nearly 30 years of MIM practice have identified several areas where design changes can greatly ease production. A few example cross-section changes are illustrated in Fig. 8.

Optimising your design for MIM production - Fig_8
Fig. 8 Design suggestions to optimise the production of metal injection moulded parts

Another geometric limitation is in the allowed corner and edge radius. Curved surfaces are generally not a problem. But the particle size dictates the edge radius.

Think of placing balls in a box – the size of the ball determines the ability to fill out corners. Stainless steel powders are available down to a few micrometers, but they are costly.

Hence, from a cost standpoint the general driver is toward nominal 20 micrometer powders, negating the production of sharp edges, in spite of the tooling. The limitation on corner and edge radius is 0.05 mm and 0.075 mm is even more realistic. Sharp edges are usually formed by grinding after sintering.

Continue to next page: Further design considerations

Download PIM International magazine

In the latest issue of PIM International…

Download PDF

Extensive MIM, CIM industry and sinter-based AM industry news, plus the following exclusive deep-dive articles and reports:

  • INMATEC Technologies: Celebrating 25 years as a driving force behind Ceramic Injection Moulding
  • A year of change: Turbulence in China’s MIM industry as markets evolve
  • Ceramic Injection Moulding: The impact of variotherm and conformal cooling technology on part quality and process capability
  • The Additive Manufacturing of multi-material and multi-functional ceramic components

The latest news from the MIM, CIM and sinter-based AM industries

Don't miss any new issue of PIM International, and stay up to date with the latest industry news. Sign up to our fortnightly newsletter.

Sign up

Join our community

Discover our magazine archive…

The free-to-access PIM International magazine archive offers unparalleled insight into the world of MIM, CIM and sinter-based AM from a commercial and technological perspective through:

  • Reports on visits to leading part manufacturers and industry suppliers
  • Articles on technology and application trends
  • Information on materials developments
  • Reviews of key technical presentations from the international conference circuit
  • International industry news

All past issues are available to download as free PDFs or view in your browser.

 

Browse the archive

 

Looking for suppliers of materials, production equipment and finished MIM, CIM or sinter-based AM parts?

Discover suppliers of these and more in our advertisers’ index and buyer’s guide, available in the back of PIM International.

  • Metal powders
  • MIM, CIM & AM parts producers
  • Binders & feedstocks
  • Feedstock mixers
  • Furnaces & furnace supplies
  • Atmospheres & gas generation
  • HIP systems & services
  • Injection moulding machines
  • AM technology
  • Debinding systems
View online
Share via
Copy link
Powered by Social Snap